REVOLABS EXECUTIVE HD™ Wireless Microphone System Models: 01-HDEXEC-NM, 01-HDEXEC4-NM, 01-HDEXEV-NM-AES, 01-HDEXEC4-NM-AES, 03-HDEXECEU-NM, 03-HDEX
- 10 - The three terminals of the BUS connector should be wired in parallel via either a daisy chain connection or terminal block split. The three con
- 11 - 1 2 3 4 5 6 7 8 on off Using the Rear Panel Configuration DIP Switches 1 – Operation Mode - Primary (off)/Secondary (on) Used when conne
- 12 - Revolabs Service Plan at the time of the system purchase, or may be purchased separately for each system. The Revolabs HD Control Panel can op
- 13 - Note: If the ‘Equipment List’ does not appear after a network scan has been performed, no devices or network connections were found or the con
- 14 - Note: Changes to the IP Configuration will take place once the Base Station’s power is cycled. System – Enable Gold: Each Executive HD Base S
- 15 - Config - Audio Mode: There are two audio modes to choose from when using an Executive HD System. ‘High Definition’ mode (default), which provi
- 16 - their previous state of individual mute capability. The ‘Tabletop Master Mute’ mode can be activated by selecting the option in the ‘config’ ta
- 17 - Monitor – Microphone Lock:* Each microphone has individual lock capabilities. By turning on the lock for a specific microphone, the microphone
- 18 - Monitor – Versions: This window provides the current firmware versions found in the Base Station. Monitor – DIP Switches: This displays the c
- 19 - When using a control system, the microphone mutes can be configured to “int. mute”, which mutes the microphone audio inside of the base station
© 2014 REVOLABS, INC. All rights reserved. No part of this document may be reproduced in any form or by any means without express written permission
- 20 - set fp 0 = Front Panel Display Lock OFF 1 = Front Panel Display Lock ON set pair* 0 = Base Pairing Lock OFF 1 = Base Pairing Lock ON get lock
- 21 - val fp 0 = Front Panel Unlocked 1 = Front Panel Locked val tm 0 = TableTop Mute Inactive 1 = TableTop Mute Active val um 0 = Mic UnMute @ St
- 22 - Biamp Audia & Nexia When using the Base Station along with a Biamp DSP, you must select the corresponding DSP product line f
- 23 - So for example, if you set the ‘Audio channels’ for the microphones to 1-8 in the Control Panel, then the Base Station will use the instance
- 24 - Channels 25-32 Revo 25 - Revo 32 Channels 33-40 Revo 33 – Revo 40 (EU & CN Versions Only) So for example, if you set the ‘Audio cha
- 25 - 3. Select Table Top Mute mode 4. Change the Low Pass Filter 5. Select DHCP or Fixed IP modes 6. Select Redundancy Mode 7. Select Power Sca
- 26 - Revolabs HD Wearable Microphones turn on and mute automatically when removed from Charger Base, to reduce noise while being attached. To use
- 27 - Turning the dial towards the earpiece, as shown in the figure, will increase the volume, and turning the dial towards the microphone will decre
- 28 - 11. With the microphone in position on the table, un-mute the microphone by pressing and releasing the Mute button (confirm by a flashing GREEN
- 29 - 5 4 3 2 1 15. With the microphone in position, un-mute the microphone by pressing and releasing the Mute button (confirm by a flashing GRE
Contents Safety and General Information ...
- 30 - 5 4 3 2 1 To use the HD Universal Wireless Adapter: 17. Remove the Microphone Adapter from the Charger Base. The adapter turns on and mutes a
- 31 - 1. Audio Out port — accepts the 2.5mm plug for the earpiece. 2. Charging Port — docks to all Revolabs HD Charger Bases. 3. Mute button — p
- 32 - 1 2 3 4 “Express Pair” is a tool in the HD Control Panel Software that can be used to pair all the microphones in a Charger Base to a Base Stat
- 33 - 1. LED indicator — power status indicator. 2. Charger Bays — charges up to 8 Microphones. 3. Mini USB Interface — computer serial in
- 34 - Please contact Revolabs (www.revolabs.com) or your AV service provider for replacement instructions and to assure the proper disposal method is
- 35 - 2. Connect the Charger Base to your computer using the Mini-USB cable provided. Make sure that the charger is plugged in and powered on and th
- 36 - Revolabs Executive HD ™ Indicator LEDs The following tables show activities associated with the various states shown by the LEDs: Equipment Us
- 37 - Revolabs Executive HD MaxSecure The Revolabs Executive HD MaxSecure product version provides AES 256 encryption of the data signal between HD M
- 38 - Warranty Revolabs, Inc. warrants this product to be free of manufacturing defects. Repair or replacement of any defective part or unit (at the
- 39 - Specifications Dimensions, (L, W, H) and Weight: Executive Base Station 16.9” (43.03 cm) x 8.0” (20.32 cm) x 1.7” (4.42 cm), 6.5 lbs. (2.95 kg
- 4 - Safety and General Information Please read the following information to ensure safe and efficient use of your Revolabs system. FCC User In
- 40 - Recommended Maximum Audio Channels: Revolabs recommends the following maximum number of active audio channels in one area (room / auditorium) a
- 41 - Index . Mini-Phoenix Connectors, 8 . On/Off Switch, 8 Adjusting the Volume, 26 Base Station, 7 Back Panel, 7 Front Panel, 7 Channel LED indicat
- 42 - Revolabs Executive HD ™ Manual 01-EXEMAN-PAP-11 April 2014 (Rev 2.8) Note: M
- 5 - product to certain destinations. For further information contact the U.S. Department of Commerce or the Canadian Department of Foreign Affairs a
- 6 - Introduction Congratulations on your purchase of a Revolabs digital wireless microphone system! This system utilizes 1.9 GHz DECT technology
- 7 - • Mixing • Acoustic echo cancellation (AEC) • Feedback elimination • Level control • Equalization • Noise cancellation The system is desig
- 8 - Controls and Connections: 1. Channel LED indicators: Displays microphone mute and pairing states. 2. Diversity Antenna: One or two sets (4 ch
- 9 - Revolabs Executive HD™ Audio Connections There are (8) 3.5mm mini-Phoenix inputs and (8) 3.5mm mini-Phoenix outputs on the back panel of the uni
Kommentare zu diesen Handbüchern